How To Reset Tire Pressure Sensor Chevy Silverado 2008

Alternatively, if your silverado does not have keyless entry, press and release the info button on the drivers information center until tire learn appears on the dic display. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.

OBD2 Auto DTCs Error Fault Code Erase Reader Reset Scanner

Listen for a double horn chirp, indicating entry into the tpm learn mode.

How to reset tire pressure sensor chevy silverado 2008. Does anyone know how to reset the tire pressure monitoring system on a 2008 silverado? Assemble the tire pressure sensor (2) to the valve stem and install the new torx screw (3). Turn on the ignition, with the engine off.

Push trip reset again to confirm; Use the tool to activate the left front sensor single horn sounds; Click set/reset and a message saying tire learning active will pop up.

Repeat the process for the passenger side front tire, passenger side rear tire, and the driver side rear tire. The horn will chirp, after the vehicle has received a signal from each sensor. Push and hold trip reset stem to begin the sensor matching process;

Keep your tire pressure monitoring system operating properly with. All you should need to do is check and set all tire pressures and make sure to check the spare also, after all tires are set with air you then drive a few blocks and the light should reset if the light does not reset then you will need to find out which wheel has a bad air pressure sensor, this is done with a tool that is put on the valve stem or a scan tool to see which tire is showing the wrong pressure,. Starting with the lf tire, use a properly formatted tpms scan tool to scan each sensor in the foll owing order:

Repeat for the rf/rr/lr sensors Using the driver instrument cluster, click the vehicle information button and navigate to relearn tire position. Tighten the torx screw to 1.3 n.m (11.5 lb in).

Push the trip odometer reset stem until tire pressure is displayed; Start from the driver side front tire, remove the valve cap, and then increasing or decreasing the tires air pressure until a horn chirp sounds. Before performing a relearn procedure, it is important to make sure the tpms sensors are installed properly, and tires are inflated to placard pressure.

Direct tpms, sensors are installed in the wheel; Relearning sensor position turn the ignition to the on position, but do not start the silverado. Press and release either arrow button until the tire pressure screen is displayed, then press the set/clr button.

Ensure the flat of the valve, lines up with the flats of the snap in the enclosure. This week, we will go over tpms diagnostics for the 2008 chevy silverado. Turn off the radio and turn the key to the on postion.

The first thing you will need to do is go to the tire you want to start with, which is the front driver's side tire. All tires are at about 38 pounds but the light is remaining on. Now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

Chevy silverado (2008) type of tpms system: I checked tire pressure and added a little air to each. Low tire pressure light is on all tire pressure is.

A horn chirp will confirm that the sensor has been reset Hold it in intell the info comes on. Push the bottom knob ( to turn the station).

Press and hold the set/reset button. Start from the driver side front tire, remove the valve cap, and then increasing or decreasing the tires air pressure until a horn chirp sounds. Using the dic, press the vehicle information button until the relearn tire positions message displays.

Lf, rf, rr and lr. After the horn chirp has sounded, repeat step. A horn chirp will confirm that the sensor has been reset

After the horn chirp has sounded, proceed as in step 4 for the next 3 sensors in the following order: My light came on two days ago. Horn will chirp twice, dic displays tire learning active;

Check if this fits your 2008 chevrolet silverado 1500. Initiate the tire pressure monitor learn mode by simultaneously pressing and holding the lock and unlock buttons on the keyless entry remote until you hear a. In the window it will show all the things you can reset.

Place your relearn tool against the sidewall closest to the valve stem (where you fill and test your psi). Repeat the process for the passenger side front tire, passenger side rear tire, and the driver side rear tire. Resetting the tire pressure sensor on your 2008 chevy silverado can be somewhat complicated, but will only take about 10 to 12 minutes of your time.

Set 4 TPMS Tire Air Pressure Sensors 315Mhz Metal fit 2014